词语大全 yield point中文翻译

Posted 2022-08-28 应力

篇首语：成长是一场温柔的修行。不是越来越强硬和尖锐，而是越来越宽宥和平和。本文由小常识网(cha138.com)小编为大家整理，主要介绍了词语大全 yield point中文翻译相关的知识，希望对你有一定的参考价值。

词语大全 yield point中文翻译

It was observed that the lower yield point was subject to a greater degree of scatter than that of the upper yield point .
业已观察到下屈服点比上屈服点易产生更大的散布度。

The conventional photoelastic modes and procedures suffice to indicate whether or not the yield point of the material of the prototype will be exceeded .
常用的光弹性模型和方法能够指明原型材料的屈服点是否将被超过。

Elastic pmit yeung \' s module of elasticity to yield point
弹性限度阳氏弹性系数及屈服点

Yield strength yield point of steel
钢材钢筋屈服强度屈服点

Yield point under bending stress
弯曲应力下的屈服点

Bending yield point
抗弯屈服点

The definition of yielding point and the non - coincidence of yielding point with extreme point
拐点的定义及拐点与极值点的不重合性

Yp yield point
屈服软化点

Analysis on the causes of no yield point in tension and brittle fracture in cold bending of 20mnsi hrb
热轧带肋钢筋冷弯脆断和无屈服点原因分析

Modern rheological test methods - part 1 : determination of the yield point - fundamentals and parative testing methods
新式流变试验方法.第1部分:屈服点的测定.基本原理和

For the obvious yield point of angle steel , the critical frictional resistance could be regarded as ultimate pullout capacity
对具有明显屈服点的钢材，在实际施工中，可以把摩阻临界值作为极限拉力。

434 we shall take the sample to test its physical properties ( mechanical properties , tensile strength , yield point , percentage elongation , reduction of area , impact value , brinell hardness )
我们将取样试验其物理性能（机械性能、抗张强度、屈服点、延伸率、断面收缩率、冲击值、布氏硬度）。

Individual dislocation - solute interactions are extrapolated to ensemble effects , including " upper yield points " during mechanical testing , serrated flow , strain aging , and viscous drag
由个别的差排溶质交互作用推衍到整体效应，包含机械测试时之上降伏点、锯齿状应力-应变行为、应变时效及黏滞力。

There were obvious yield point jog both when the a3 steel specimen are under monotonic tension and pure torsion , this illustrates that there are obvious physical yield procedure in these process
A3钢试件在单一拉伸和纯扭转时都有明显的屈服平台，这说明a3钢试件在单一拉伸和纯扭转时都有明显的物理屈服过程。

According to the test results of locapzation and shear bands formation under the consopdated undrained plane strain pression tests on soft clay in shanghai , it was found that the deviator stress of shear band beginning to form was very close to its yield point in clay soils
摘要根据上海软土在固结不排水平面应变压缩试验条件下应变局部化和剪切带形成的实测研究结果，发现粘性土剪切带开始形成的偏应力为其屈服点。

It was observed , from experiments , that this alloy presented abnormal performance after undergoing low strain rate and high - temperature deformation . the flow stress reduced to only one percent of the yield point at room temperature and the elongation to fracture increase ice
试验发现： 480下ly12经历低应变速率拉伸后，将其冷却至室温，性质会发生极大变化：流动应力只有普通室温屈服应力的十分之一左右；延伸率比通常条件下增加一倍左右。

Although cold - formed rectangular tube - steel column is favorable to industriapzation of mass production , the cold forming process increase the yield point and tensile strength , at the same time the cold forming process decrease the ductile behavior , so it ’ s necessary to research the seismic behavior of cold - formed rectangular tube - steel column for architecture structure
冷弯矩形钢管虽然可以实现大批量工厂化生产,但冷弯矩形钢管在冷成型过程提高了材料的屈服点和抗拉强度同时降低了延性,因而冷弯矩形钢管作为柱材在建筑结构抗震中的应用有待进一步研究。

In terms of strength and ductipty , the concept of specified yield point is put forward . based on the principle that under the same condition ( that is , the size of cross section , material strength and reinforcement ratio are identical ) , the resultant ultimate moment must be identical , the pression failure of frp reinforced concrete beam is equal to the tension failure for the viewpoint of design and calculation
从强度与延性两方面的综合考虑，提出了纤维增强塑料筋名义屈服点的概念，对发生受压破坏的纤维增强塑料筋混凝土梁，按照同样条件下(截面尺寸、材料强度、截面配筋率等均相同)截面承载力相等的原则等效转化为受拉破坏进行设计与计算，以此确定纤维增强塑料筋的强度折减系数_ f 。

Through the strong pulpng tests of four kinds of synthetic fiber filter cloth , the mechanical performance index of the filter cloth in dry and wet conditions were measured , the influence of various pulpng speeds on the fracture strength and the fracture tensile rate of the filter cloth was derived . it was concluded that the stress of the filter cloth could relax when it was beyond the yield point
通过4种合成纤维滤布的强力拉伸试验，测得了滤布在干、湿两种状态下的力学性能指标，得出了不同拉伸速度对滤布断裂强度和断裂伸长率的影响，同时指出当滤布的应力超过屈服点时，会出现应力松驰现象。