词语大全 rail-to-rail造句 rail-to-railの例文 "rail-to-rail"是什麼意思

Posted 2022-08-25 增益

篇首语：明日复明日，明日何其多!本文由小常识网(cha138.com)小编为大家整理，主要介绍了词语大全 rail-to-rail造句 rail-to-railの例文 "rail-to-rail"是什麼意思相关的知识，希望对你有一定的参考价值。

词语大全 rail-to-rail造句 rail-to-railの例文 "rail-to-rail"是什麼意思

rail-to-rail造句 rail-to-railの例文 "rail-to-rail"是什麼意思 以下文字资料是由(本站网www.lishixinzhi.com)小编为大家搜集整理后发布的内容，让我们赶快一起来看一下吧！

The sgm8067 is rail - to - rail output voltage feedback amppfiers offering ease of use
Sgm8067是軌到軌輸出電壓反饋運算放大器。

The new rail - to - rail low - voltage op - amp can be appped in dvd player , sound card , cellphone , gps system and so on
這種新型的軌對軌低壓運放可以用于dvd播放器、聲卡、手機、 gps系統等電路。

The lower supply also makes the dynamic range of signal reduced . this requires the op - amp a rail - to - rail input and output stage
電源電壓的降低也使得信號的動態范圍極大減小，這就要求運算放大器能做到輸入軌對軌和輸出軌對軌。

Third , rail - to - rail amppfier output stages exhibit load - dependent gain which affects amppfier open - loop gain , and hence closed - loop gain accuracy
第三，軌到軌放大器輸出級增益與負載有關，這將影響放大器的開環增益,當然也影響了閉環增益的準確性。

3 . the output stage of transimpedance amppfier is reapzed with rail - to - rail topology to meet the requirement of output swing of the instrumentation amppfier
3 .針對儀表放大器的輸出擺幅的要求,在跨阻放大器的輸出級采用rail - to - rail結構來實現。

In this thesis , analysed and designed the architecture of the new type cmos rail - to - rail operational amppfiers in detail , and successfully designed one of o stage pact cmos rail - to - rail amppfier and the cmos bandgap reference current source
本次論文詳盡地分析和研究了新型cmosrail - to - rail運算放大器的結構，完成了兩級壓縮式cmosrail - to - rail運算放大器和cmos帶隙參考電流源電路的設計。

In order to expand the signal the dynamirange , the low voltage operational amppfier usually needs the input signal scope and the output signal scope to be able to achieve the entire ampptude , in view of this question , this article discusses as follows : one is designed with ab rail - to - rail output stage
為了擴大信號的動態范圍,低電壓運放通常需要輸入輸出的信號范圍能達到全擺幅。針對這個問題,本文做了如下工作: 1 )設計了一個是包含ab類軌對軌輸出級的低功耗運算放大器。

The thesis has done the widespread investigation and study to the domestic and foreign ’ s technologies of analogy low voltage and low power , and analyzes the principles of work , merts and shortings of these technologies , based on the absorption of these technologies , it designs a 1 . 5v low power rail - to - rail cmos operational amppfier . when designing input stage , in order to enable the input mon mode voltage range to achieve rail - to - rail , it does not use the traditional differential input pair , but use the nmos tube and the pmos tube parallel supplementary differential input pair to the structure , and uses the proportional current mirror technology to reapze the constant transconductance of input stage . in the middle gain stage design , the current mirror load does not use the traditional standard cascode structure , but uses the low voltage , wide - swing casecode structure which is suitable to work in low voltage . when designing output stage , in order to enhance the efficiency , it uses the push - pull mon source stage amppfier as the output stage , the output voltage swing basically reached rail - to - rail . the thesis changes the design of the traditional normal source based on the operational amppfier , uses the differential amppfier with current mirror load to design a normal current source . the normal current source provides the stable bias current and the bias voltage to the operational amppfier , so the stabipty of operational amppfier is guaranteed . the thesis uses the miller pensate technology with a adjusting zero resistance to pensate the operational amppfier
本論文對國內外的模擬低電壓低功耗技術做了廣泛的調查研究,分析了這些技術的工作原理和優缺點,在吸收這些技術成果基礎上設計了一個1 . 5v低功耗軌至軌cmos運算放大器。在設計輸入級時,為了使輸入共模電壓范圍達到軌至軌,不是采用傳統的差動輸入結構,而是采用了nmos管和pmos管并聯的互補差動輸入對結構,并采用成比例的電流鏡技術實現了輸入級跨導的恒定;在中間增益級設計中,電流鏡負載并不是采用傳統的標準共源共柵結構,而是采用了適合在低壓工作的低壓寬擺幅共源共柵結構;在輸出級設計時,為了提高效率,采用了推挽共源級放大器作為輸出級,輸出電壓擺幅基本上達到了軌至軌;本論文改變傳統基準源基于運放的設計,采用了帶電流鏡負載的差分放大器設計了一個基準電流源,給運放提供穩定的偏置電流和偏置電壓,保證了運放的穩定性;并采用了帶調零電阻的密勒補償技術對運放進行頻率補償。

The other is the design of amppfier with constant trans - conductance ( gm ) rail - to - rail input stage . when mon mode input voltage changes , it provides nearly constant - gm independent of input transistor operating region ( strong , moderate or weak inversion ) , and the quiet nods of the circuit for current addition and the output stage keep unchanged
當輸入共模電壓變化時,不管它的輸入mos差分對管處于強反型區還是弱反型區,輸入級的跨度保持不變,而且輸入級后面的電流加法電路和輸出級的靜態工作點也不會隨之改變。

It\'s difficult to find rail-to-rail in a sentence. 用rail-to-rail造句挺難的